- 您现在的位置：买卖IC网 > Sheet目录503 > RN41-I/RM (Microchip Technology)MODULE BLUETOOTH W/ANT CLASS1
RN -41 -DS
?
DESIGN CONCERNS ?
The following sections provide information on designing with the RN-41 module, including radio interference, factory reset,
solder reflow profile, connection status, etc.
Reset Circuit
The RN-41 contains a 1k pullup to VCC, and the reset polarity is active low. The module’s reset pin has an optional power-
on-reset circuit with a delay, which should only be required if the input power supply has a very slow ramp or tends to
bounce or have instability on power up. Often a microcontroller or embedded CPU I/O is available to generate the reset
once power is stable. If not, designers can use one of the many low-cost power supervisor chips currently available, such
as the MCP809, MCP102/121, and Torex XC61F.
Factory Reset Using GPIO4
Roving Networks recommends that designers connect the GPIO4 pin to a switch, jumper, or resistor so it can be accessed.
This pin can be used to reset the module to its factory default settings, which is critical in situations where the module has
been misconfigured. To reset the module to the factory defaults, GPIO4 should be high on power-up and then toggle low,
high, low, high with a 1 second wait between the transitions.
Connection Status
GPIO5 is available to drive an LED, and it blinks at various speeds to indicate status (see Table 7). GPIO2 is an output that
directly reflects the connection state as shown in Table 8.
Table 7. GPIO5 Status
GPIO5 Status
Toggle at 1 Hz
Toggle at 10 Hz
High
Table 8. GPIO2 Status
GPIO2 Status
High
Low
Description
The module is discoverable and waiting for a connection.
The module is in command mode.
The module is connected to another device over Bluetooth.
Description
The module is connected to another device over Bluetooth.
The module is not connected over Bluetooth.
HCI Mode
Roving Networks offers the Host Controller Interface (HCI) mode in addition to the standard operational mode of its
Bluetooth modules (standard mode refers to the on-board stack running on the module).
In HCI mode, the on-board stack is bypassed and the module is put in a state that runs the Bluetooth baseband. The HCI
provides a command reference interface to the baseband controller and the link manager, and provides access to the
hardware status and control registers. This interface provides a uniform method for accessing the Bluetooth baseband
capabilities.
www.rovingnetworks.com
Version 3.3r 4/9/2012
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
RN42N-I/RM
MODULE BLUETOOTH V2.0+EDR
RP1A090ZPTR
MOSFET P-CH 12V 9A MPT6
RP1E050RPTR
MOSFET P-CH 30V 5A MPT6
RP1E090RPTR
MOSFET P-CH 30V 9A MPT6
RP1E100RPTR
MOSFET P-CH 30V 10A MPT6
RPM-012PBT97
PHOTOTRANSISTOR SIDE VIEW SMD
RPM-20PBM
PHOTOTRANSISTOR 800NM SIDE VIEW
RPM-22PB
PHOTOTRANSISTOR 800NM SIDE VIEW
相关代理商/技术参数
RN41-I/RM-CUT TAPE
制造商:Microchip 功能描述:RN-41 Series Class 1 Fully Qualified 3 Mbps Bluetooth Module
RN41K2A1002F BULK
制造商:KOA Speer Electronics Inc 功能描述:10.0K ohm 100ppm SM RES-METAL FILM MELF 0805 1% 125mW 制造商:KOA Speer Electronics Inc 功能描述:10.0K ohm 100ppm SM RES-METAL FILM MELF 0805 1% 125mW - free partial T/R at 500.
RN41K2A2002F BULK
制造商:KOA Speer Electronics Inc 功能描述:20.0K ohm 100ppm SM RES-METAL FILM MELF 0805 1% 125mW 制造商:KOA Speer Electronics Inc 功能描述:20.0K ohm 100ppm SM RES-METAL FILM MELF 0805 1% 125mW - free partial T/R at 500.
RN41L2HT3.3KJ
制造商:KOA Speer Electronics Inc 功能描述:
RN-41-N
制造商:未知厂家 制造商全称:未知厂家 功能描述:RN-41/RN-41-N Class 1 Bluetooth Module
RN-41-N-HCI
制造商:未知厂家 制造商全称:未知厂家 功能描述:RN-41/RN-41-N Class 1 Bluetooth Module
RN-41-N-HID
制造商:未知厂家 制造商全称:未知厂家 功能描述:RN-41/RN-41-N Class 1 Bluetooth Module
RN41N-I/RM
功能描述:蓝牙/802.15.1 模块 Class1 v 2.1 surface mount, no antenna RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm